 |
XY-GN9004A
Xiyuan
Multi channel eDAQ vibrating wire acquisition instrument, Edge Computing Data Collector, Industrial Data Acquisition
| Dynamic input | Number of channels | 4 | |
| A/D bit number | 24 | ||
| Input method | Voltage/IEEE/4-20mA | ||
| Signal input bandwidth | Voltage/4-20mA | DC-50kHz | |
| IEPE | 0.3Hz-50kHz（-3dB） | ||
| Slow variable simulation input | Number of channels | 4 | |
| A/D bit number | 16 | ||
| Input method | Voltage/4-20mA | ||
| Signal Input Bandwidth | DC-100Hz | ||
 | 1, Dynamic input: A1, A2, A3, A4 corresponds to four channels of dynamic signal input, the highest sampling rate of 128kSPS, each channel wiring is the same, the left figure is the A1 channel wiring diagram, the factory default is to be connected to the IEPE sensor, if you need to be connected to the voltage / 4-20mA type sensors, need to be specified when ordering. Each channel's pin 1 can provide 24V power supply for external sensors, maximum 50mA current, if external sensors need to use the 1-pin power supply, please pay attention to check the wiring to avoid damage caused by the wrong line. | |
| 2,Analog input: B1, B2, B3, B4 correspond to 4 channels of slow variable analog signal input, each channel wiring is the same, the following figure is the B1 channel wiring diagram, the factory default is to be connected to the voltage input sensor, if you need to be connected to the 4-20mA type sensors, need to be specified when ordering. Each channel's pin 1 can provide 24V power for external sensors, maximum 50mA current, if the external sensors need to use the 1-pin power supply, please pay attention to check the wiring to avoid damage caused by the wrong line. |  | |
 |  |  |
| 3, RPM and RS485 interface: The first set of 485 interfaces (A1,B1) is available, the second set of 485 interfaces is reserved for system backup. | 4,Digital input and output interface: Digital input port (low level: about 0.4V, high level: about 23V) Digital output port (low level: about 0.4V, high level: about 23V) | 5,Power supply interface: Before connecting the power supply, please make sure that the external power supply provided meets the needs of the instrument. |
Multi channel eDAQ vibrating wire acquisition instrument, Edge Computing Data Collector, Industrial Data Acquisition
| Dynamic input | Number of channels | 4 | |
| A/D bit number | 24 | ||
| Input method | Voltage/IEEE/4-20mA | ||
| Signal input bandwidth | Voltage/4-20mA | DC-50kHz | |
| IEPE | 0.3Hz-50kHz（-3dB） | ||
| Slow variable simulation input | Number of channels | 4 | |
| A/D bit number | 16 | ||
| Input method | Voltage/4-20mA | ||
| Signal Input Bandwidth | DC-100Hz | ||
| 1, Dynamic input: A1, A2, A3, A4 corresponds to four channels of dynamic signal input, the highest sampling rate of 128kSPS, each channel wiring is the same, the left figure is the A1 channel wiring diagram, the factory default is to be connected to the IEPE sensor, if you need to be connected to the voltage / 4-20mA type sensors, need to be specified when ordering. Each channel's pin 1 can provide 24V power supply for external sensors, maximum 50mA current, if external sensors need to use the 1-pin power supply, please pay attention to check the wiring to avoid damage caused by the wrong line. | |
| 2,Analog input: B1, B2, B3, B4 correspond to 4 channels of slow variable analog signal input, each channel wiring is the same, the following figure is the B1 channel wiring diagram, the factory default is to be connected to the voltage input sensor, if you need to be connected to the 4-20mA type sensors, need to be specified when ordering. Each channel's pin 1 can provide 24V power for external sensors, maximum 50mA current, if the external sensors need to use the 1-pin power supply, please pay attention to check the wiring to avoid damage caused by the wrong line. | | |
| | |
| 3, RPM and RS485 interface: The first set of 485 interfaces (A1,B1) is available, the second set of 485 interfaces is reserved for system backup. | 4,Digital input and output interface: Digital input port (low level: about 0.4V, high level: about 23V) Digital output port (low level: about 0.4V, high level: about 23V) | 5,Power supply interface: Before connecting the power supply, please make sure that the external power supply provided meets the needs of the instrument. |
